npub1yrlmnr0y2ch5ycn38j2navyduf5q6tqyd0led3p7xhwmzwcrlsaq558gpm (npub1yrl…8gpm)
Aslo, only PLA cones off easily. The shrinking of ABS can even break a plate. This was the cause of my last two chips in my glas.
For a standard ABS print, like 10x10cm I might use Dimafix on corners, but my hot-bed and enclosure prevents warping. But if I were to print my full bed size, I use something like glue-stick, just because it can either stick too well due to the large surface or even the 0.5% shrinkage can shatter the glass.
You've told me before that PC warps. This is due to shrinkage when cooling. So my experienced guess would be to do it if you find it to stick quite well.
npub12atwfrq4rfv7fqara6gzsgrgj7k8ngewzl5nzs46agwyxzh0e25qxlme5y (npub12at…me5y) #3dprinting
Stark /
npub1du…mrdxt
2023-09-22 12:30:54
in reply to nevent1q…rj66
Author Public Key
npub1du3s0yz2jtnhzckdvatn0fdd07htywny8p6lwas93ekqlzxnyxaqumrdxtPublished at
2023-09-22 12:30:54Event JSON
{
"id": "d96013e6af82726b8f5cf2351294279189fccdcf1fb16376177cc6f1ed9b37ec",
"pubkey": "6f2307904a92e77162cd675737a5ad7faeb23a643875f776058e6c0f88d321ba",
"created_at": 1695385854,
"kind": 1,
"tags": [
[
"p",
"20ffb98de4562f4262713c953eb08de2680d2c046bff96c43e35ddb13b03fc3a",
"wss://relay.mostr.pub"
],
[
"p",
"5756e48c151a59e483a3ee9028206897ac79a32e17e93142baea1c430aefcaa8",
"wss://relay.mostr.pub"
],
[
"p",
"ea01c28d25fdebef270fb11977d88794eaa6e04210af4e9f0d45d2ca4df3e28e",
"wss://relay.mostr.pub"
],
[
"p",
"02a0f2cd76233181ace57dc1bcc8c69d14efd1b973613d49e6e28b2cb89aee30",
"wss://relay.mostr.pub"
],
[
"e",
"2798eedbb6cc67fda63f333ecedd236727262d592dc61e057070ffb4f2ab411f",
"wss://relay.mostr.pub",
"reply"
],
[
"t",
"3dprinting"
],
[
"proxy",
"https://techhub.social/users/Stark9837/statuses/111108807387987998",
"activitypub"
]
],
"content": "nostr:npub1yrlmnr0y2ch5ycn38j2navyduf5q6tqyd0led3p7xhwmzwcrlsaq558gpm \n\nAslo, only PLA cones off easily. The shrinking of ABS can even break a plate. This was the cause of my last two chips in my glas.\n\nFor a standard ABS print, like 10x10cm I might use Dimafix on corners, but my hot-bed and enclosure prevents warping. But if I were to print my full bed size, I use something like glue-stick, just because it can either stick too well due to the large surface or even the 0.5% shrinkage can shatter the glass.\n\nYou've told me before that PC warps. This is due to shrinkage when cooling. So my experienced guess would be to do it if you find it to stick quite well.\n\nnostr:npub12atwfrq4rfv7fqara6gzsgrgj7k8ngewzl5nzs46agwyxzh0e25qxlme5y #3dprinting",
"sig": "b1c4596939e3d68660fdc5c5534847c9a42c2e3d07ec99e2541da85d72896c1f7c8a09e79c565486ff581ac8de4689cdb9a660f4a98e89f02a3cecf0a2bc7f72"
}