#greenhouse #mining update
After cleaning the malfunction temp sensor and mounting the heat sink I did another test.
I am using #braiins os because I have installed to silent sensors and the #antminer #firmware thinks the fan is not working properly because they require lower frequency.
braiins os shows me temperature of the #miner for the first few minutes but after it disappears and miner is reducing #hashrate.
It shows me error messages (I posted earlier) of the temperature sensor.
I saw in some forums that antminer #firmware is showing better error logs so I assambled the old fans and started the miner with the antminer firmware.
And yes this firmware shows me there are 2 temperature sensors and one is fully working and the other one brings an error with the first read attempt.
The antminer firmware is not reducing hashrate, but rather sets fan speed to always full power.
What means I could run this #hashboard using this firmware.
Anyhow I can´t, because the noise would ran my neighbor crazy
So my options are:
1. Finding a way to use antminer firmware with the silent fans
2. Find a way in Braiins OS to act like the antminer firmware
3. Find another OS
4. Replace the malfunction chip. But here I need to find out if the sensor itself is the problem or any connected component (capacitor or resistor)
I guess I will go with option 4
Maybe #nostr has got any advice?
#asknostr #diy #project #orangery
orangery
npub1en…0st7h
2024-10-28 19:29:34
Author Public Key
npub1enquef7852nmqsvgy0sex32gc3slsdrp6u9rf8euygpwds8n394s00st7hPublished at
2024-10-28 19:29:34Event JSON
{
"id": "dd0ca0e022652741aff49e54f83c77134f4f9b7f1a4f8c9a71d61e5a3986634a",
"pubkey": "ccc1cca7c7a2a7b0418823e1934548c461f83461d70a349f3c2202e6c0f3896b",
"created_at": 1730143774,
"kind": 1,
"tags": [
[
"t",
"greenhouse"
],
[
"t",
"mining"
],
[
"t",
"braiins"
],
[
"t",
"antminer"
],
[
"t",
"firmware"
],
[
"t",
"miner"
],
[
"t",
"hashrate"
],
[
"t",
"hashboard"
],
[
"t",
"nostr"
],
[
"t",
"asknostr"
],
[
"t",
"diy"
],
[
"t",
"project"
],
[
"t",
"orangery"
],
[
"client",
"noStrudel",
"31990:266815e0c9210dfa324c6cba3573b14bee49da4209a9456f9484e5106cd408a5:1686066542546"
]
],
"content": "#greenhouse #mining update\nAfter cleaning the malfunction temp sensor and mounting the heat sink I did another test. \nI am using #braiins os because I have installed to silent sensors and the #antminer #firmware thinks the fan is not working properly because they require lower frequency. \nbraiins os shows me temperature of the #miner for the first few minutes but after it disappears and miner is reducing #hashrate. \nIt shows me error messages (I posted earlier) of the temperature sensor. \nI saw in some forums that antminer #firmware is showing better error logs so I assambled the old fans and started the miner with the antminer firmware. \n\nAnd yes this firmware shows me there are 2 temperature sensors and one is fully working and the other one brings an error with the first read attempt. \nThe antminer firmware is not reducing hashrate, but rather sets fan speed to always full power. \nWhat means I could run this #hashboard using this firmware. \nAnyhow I can´t, because the noise would ran my neighbor crazy\n\nSo my options are: \n1. Finding a way to use antminer firmware with the silent fans\n2. Find a way in Braiins OS to act like the antminer firmware\n3. Find another OS \n4. Replace the malfunction chip. But here I need to find out if the sensor itself is the problem or any connected component (capacitor or resistor)\n\nI guess I will go with option 4\nMaybe #nostr has got any advice?\n#asknostr #diy #project #orangery",
"sig": "d16dd03aaf5cc852071fd822a13b4ea32292da8fcf59529fcb1e1e2282a97b478f0f98c7fb9ddaa4f54d6cbb1bc968e07b337ae2bdcb5459bfd282f71519fbc5"
}